Just recently purchased the USB-UIRT and extremely happy with it. Installation and learning have gone smoothly with the exception of X10 IR codes. I have used both an X10 remote in IR mode and a Universal MX-500 remote but have not had any luck with either. Has anyone else experienced this problem and if so were you able to come up with any work arounds?
Thanks for any assistance you can provide.
Learning X10 IR Codes
Moderator: jrhees
18 posts
• Page 1 of 2 • 1, 2
by jrhees » Wed Oct 22, 2003 2:26 pm
Guest,
I have an X-10 IR/RF remote handy -- can you some specific buttons to look at? How do you tell the X-10 remote to send X-10 commands out in IR (or do they always come out both RF *and* IR?
Thanks,
Jon
I have an X-10 IR/RF remote handy -- can you some specific buttons to look at? How do you tell the X-10 remote to send X-10 commands out in IR (or do they always come out both RF *and* IR?
Thanks,
Jon
- jrhees
- Site Admin
- Posts: 1652
- Joined: Tue Jan 28, 2003 11:49 pm
by althea5266 » Wed Oct 22, 2003 8:53 pm
Jon,
Thanks for your quick response. Sorry, I wasn't logged in when I sent first message. The remote only send IR or RF. It uses a device code to determine which to send. When I select the X10 device it sends out RF and I have programmed the AUX with the IR code. To turn on an X10 module, you select the number and then hit the Channel Up button. For off, number then Channel Down. Not sure what remote you have but the device codes for mine are 999 for RF, 998 for IR. Can provide additional details if you need.
Thanks,
Mark
________
Ship Sale
Thanks for your quick response. Sorry, I wasn't logged in when I sent first message. The remote only send IR or RF. It uses a device code to determine which to send. When I select the X10 device it sends out RF and I have programmed the AUX with the IR code. To turn on an X10 module, you select the number and then hit the Channel Up button. For off, number then Channel Down. Not sure what remote you have but the device codes for mine are 999 for RF, 998 for IR. Can provide additional details if you need.
Thanks,
Mark
________
Ship Sale
Last edited by althea5266 on Thu Mar 10, 2011 3:19 am, edited 1 time in total.
- althea5266
- Posts: 5
- Joined: Wed Oct 22, 2003 12:51 pm
by jrhees » Wed Oct 22, 2003 10:40 pm
Mark,
The remote I have is their 'Super Remote' model UR19a. After looking up the manual at ftp://ftp.x10.com/pub/manuals/ur19a_om.pdf I found that I had to either choose IR or RF for the X-10 stuff (device code 14 for IR). Once I selected IR I was able to Learn codes into Girder. I don't have an IR receiver, though, so I can't test transmit.
Can you give me more of a description of what is not working for you. --Are you able to Learn but the codes don't work, etc.?
-Jon
The remote I have is their 'Super Remote' model UR19a. After looking up the manual at ftp://ftp.x10.com/pub/manuals/ur19a_om.pdf I found that I had to either choose IR or RF for the X-10 stuff (device code 14 for IR). Once I selected IR I was able to Learn codes into Girder. I don't have an IR receiver, though, so I can't test transmit.
Can you give me more of a description of what is not working for you. --Are you able to Learn but the codes don't work, etc.?
-Jon
- jrhees
- Site Admin
- Posts: 1652
- Joined: Tue Jan 28, 2003 11:49 pm
by althea5266 » Thu Oct 23, 2003 1:15 am
Jon,
I was using a different model but had a UR19A here as well. Set that up for IR and was able to learn codes through Girder (took longer than with commands for my TV) but the codes are not working when testing. The commands for other devices are esily learned and working. The code learned for a Channel Up command was:
004B15534A7E4A1761303F1300000000000000000000000000
Not sure if this helps but you can at least see if it matches your results.
Thanks,
Mark
________
Vaporizers
I was using a different model but had a UR19A here as well. Set that up for IR and was able to learn codes through Girder (took longer than with commands for my TV) but the codes are not working when testing. The commands for other devices are esily learned and working. The code learned for a Channel Up command was:
004B15534A7E4A1761303F1300000000000000000000000000
Not sure if this helps but you can at least see if it matches your results.
Thanks,
Mark
________
Vaporizers
Last edited by althea5266 on Thu Mar 10, 2011 3:19 am, edited 1 time in total.
- althea5266
- Posts: 5
- Joined: Wed Oct 22, 2003 12:51 pm
by althea5266 » Thu Oct 23, 2003 10:15 pm
Jon,
Tried out your suggestion but still no luck getting the learned code to work. Can you suggest anything else to try?
Thanks,
Mark
________
Justin bieber fans
Tried out your suggestion but still no luck getting the learned code to work. Can you suggest anything else to try?
Thanks,
Mark
________
Justin bieber fans
Last edited by althea5266 on Thu Mar 10, 2011 3:19 am, edited 1 time in total.
- althea5266
- Posts: 5
- Joined: Wed Oct 22, 2003 12:51 pm
by jrhees » Thu Oct 23, 2003 10:34 pm
Mark,
OH! I just thought of something else you definitely *SHOULD* try:
Try re-learning the remote code but after hitting the Learn button, CHECK the 'Force Raw Learn' checkbox and then learn the code. Then try testing the code with repeat of 10, etc. etc.
-Jon
OH! I just thought of something else you definitely *SHOULD* try:
Try re-learning the remote code but after hitting the Learn button, CHECK the 'Force Raw Learn' checkbox and then learn the code. Then try testing the code with repeat of 10, etc. etc.
-Jon
- jrhees
- Site Admin
- Posts: 1652
- Joined: Tue Jan 28, 2003 11:49 pm
by althea5266 » Thu Oct 23, 2003 10:51 pm
Jon,
The 'Force Raw Learn' box did the trick, even with the Repeat set at 4. One more quick question if I can. How do I use the Code 1, Code 2 boxes when learning codes? Always seems to fill the Code 1 area even if I move the cursor to the Code 2 box.
Thanks for all your help and the support you provide.
Mark
________
RHODE ISLAND DISPENSARY
The 'Force Raw Learn' box did the trick, even with the Repeat set at 4. One more quick question if I can. How do I use the Code 1, Code 2 boxes when learning codes? Always seems to fill the Code 1 area even if I move the cursor to the Code 2 box.
Thanks for all your help and the support you provide.
Mark
________
RHODE ISLAND DISPENSARY
Last edited by althea5266 on Thu Mar 10, 2011 3:19 am, edited 1 time in total.
- althea5266
- Posts: 5
- Joined: Wed Oct 22, 2003 12:51 pm
by jrhees » Thu Oct 23, 2003 10:53 pm
Don't worry about the Code1 and Code2 boxes. These are the USB-UIRT-specific codes which are stored in the Girder .GML file. Some remote control protocols send two different codes (a single code followed by a different repeat code), and in those cases 'Code2' will hold the unique repeated code.
-Jon
-Jon
- jrhees
- Site Admin
- Posts: 1652
- Joined: Tue Jan 28, 2003 11:49 pm
by althea5266 » Thu Oct 23, 2003 11:15 pm
Last edited by althea5266 on Thu Mar 10, 2011 3:19 am, edited 1 time in total.
- althea5266
- Posts: 5
- Joined: Wed Oct 22, 2003 12:51 pm
x10
by AirPost » Fri Mar 19, 2004 5:11 am
Hello,
Can anyone please help me with my x10 remote. I have a UR74A 5-in-one remote from X10 and it controls my x10 modules fine. What I want is to have girder learn the x10 commands through USB-UIRT. Everytime I learn the commands, there is no command being received by the USB-UIRT. I'm pretty sure this remote sends out IR commands so girder and USB-UIRT should receive the commands fine but it doesn't see it. Tried the RAW mode but still no luck.
Can anyone please help me with my x10 remote. I have a UR74A 5-in-one remote from X10 and it controls my x10 modules fine. What I want is to have girder learn the x10 commands through USB-UIRT. Everytime I learn the commands, there is no command being received by the USB-UIRT. I'm pretty sure this remote sends out IR commands so girder and USB-UIRT should receive the commands fine but it doesn't see it. Tried the RAW mode but still no luck.
- AirPost
- Posts: 3
- Joined: Sun Feb 29, 2004 11:59 am
18 posts
• Page 1 of 2 • 1, 2
Who is online
Users browsing this forum: No registered users and 6 guests